首页 > 产品展厅 > PP PE PVC CPVC > 电线电缆PP专用料陶氏杜邦 DF...

电线电缆PP专用料陶氏杜邦 DFDA-1638 NT

2020-10-16

产品详情

产地陶氏杜邦
价格：12
产品名称电线电缆PP专用料陶氏杜邦 DFDA-1638 NT 查看相似产品 >

简介

UNIGARD™ RE DFDA-1638 NT

Non-Halogen, Flame Retardant, Thermoplastic Jacket and Insulation Compound

The Dow Chemical Company

产品说明：

彩色护套/各种电信和工业应用

UNIGARD™ RE DFDA-1638 NT 物性表

基本信息
添加剂	紫外线稳定剂
用途	Flame Retardant Jacketing Industrial Cable Jacketing LSZH Jacketing 电线电缆应用通信电线护套
机构评级	IEEE 383 UL 1685 UL VW-1
形式	粒子

物理性能	额定值	单位制	测试方法
密度	1.50	g/cm3	ASTM D1505
Mechanical Water Absorption - 7 days (70°C)	9.50	mg/in2	UL 1581

机械性能	额定值	单位制	测试方法
耐磨耗性 - 1000 cycle	2	%	ASTM D1044
Shrinkback - 4 hrs (100°C) 1	1.0	%	REA 89

老化	额定值	单位制	测试方法
拉伸强度保持率 - 10 days (110°C) 2	110	%	ASTM D638
伸长保持率 - 10 days (110°C) 3	89	%	ASTM D638

热性能	额定值	单位制	测试方法
热变形 4			UL 1581
90°C	2.8	%	UL 1581
100°C	10	%	UL 1581
121°C	48	%	UL 1581
氧感应时间 - Al pans, no crimping, no screen, 100 ml oxygen/min	25	min	ASTM D3895

可燃性	额定值	单位制	测试方法
Acid Gas Test - Generation	0.47	%	MIL C-24643
毒性	1.40		NES 713
酸性气体排放 pH	4.50		IEC 754-2
酸性气体排放传导性	No conductivity increase of the test fluid		IEC 754-2
温度指数（燃烧） - Critical	> 350	°C	NES 715
烟雾 (2.54 mm)	5.30		NES 711
烟雾密度			ASTM E662
Flaming Mode - D1.5 : 2.54 mm	0.62		ASTM E662
Flaming Mode - D4.0 : 2.54 mm	1.0		ASTM E662
Flaming Mode - Dm, (corr.) : 2.54 mm	82		ASTM E662
Non-flaming Mode - D1.5 : 2.54 mm	0.24		ASTM E662
Non-flaming Mode - D4.0 : 2.54 mm	16		ASTM E662
Non-flaming Mode - Dm, (corr.) : 2.54 mm	290		ASTM E662

物理性能	额定值	单位制	测试方法
抗环境应力开裂 5(10% Igepal)	720	hr	ASTM D1693

硬度	额定值	单位制	测试方法
肖氏硬度 (邵氏 A)	89		ASTM D2240

机械性能	额定值	单位制	测试方法
抗张强度 6	12.4	MPa	ASTM D638
伸长率 7(断裂)	180	%	ASTM D638
弯曲模量 - 1% 正割	214	MPa	ASTM D790

弹性体	额定值	单位制	测试方法
撕裂强度	6.13	kN/m	ASTM D470

热性能	额定值	单位制	测试方法
脆化温度	-25.0	°C	ASTM D746

电气性能	额定值	单位制	测试方法
体积电阻率 (23°C)	3.5E+14	ohms·cm	ASTM D257
介电常数			ASTM D150
60 Hz	3.42		ASTM D150
100 kHz	3.49		ASTM D150
1 MHz	3.42		ASTM D150
6 MHz	3.34		ASTM D150
耗散因数			ASTM D150
60 Hz	3.7E-3		ASTM D150
100 kHz	7.6E-3		ASTM D150
1 MHz	0.014		ASTM D150
6 MHz	0.016		ASTM D150

可燃性	额定值	单位制	测试方法
极限氧指数	39	%	ASTM D2863

补充信息
Fluid Resistance:Diesel Fuel, MIL-F-16884, 24 hrs, 35°C #14 AWG (1.63 mm dia.) solid copper conductor with 0.045 in (1.1 mm) insulation. Full immersion of tubular specimens. Tensile Strength Retention: 77% Elongation Retention: 101% Hydraulic Fuel, MIL-H-5606, 24 hrs, 49°C #14 AWG (1.63 mm dia.) solid copper conductor with 0.045 in (1.1 mm) insulation. Full immersion of tubular specimens. Tensile Strength Retention: 61% Elongation Retention: 93% Hydraulic Fuel, MIL-H-17672, 24 hrs, 49°C #14 AWG (1.63 mm dia.) solid copper conductor with 0.045 in (1.1 mm) insulation. Full immersion of tubular specimens. Tensile Strength Retention: 73% Elongation Retention: 111% Lubricating Oil, MIL-L-23699, 24 hrs, 49°C #14 AWG (1.63 mm dia.) solid copper conductor with 0.045 in (1.1 mm) insulation. Full immersion of tubular specimens. Tensile Strength Retention: 80% Elongation Retention: 124% ASTM #2 Oil, 4 hrs, 70°C #14 AWG (1.63 mm dia.) solid copper conductor with 0.045 in (1.1 mm) insulation. Full immersion of tubular specimens. Tensile Strength Retention: 68% Elongation Retention: 139% Turbine Fuel, JP-4, MIL-T-5624, 24 hrs, 23°C #14 AWG (1.63 mm dia.) solid conductor with 0.030 in (0.76 mm) insulation. Full immersion of tubular specimens. Tensile Strength Retention: 76% Elongation Retention: 160% Turbine Fuel, JP-5, MIL-T-5624, 24 hrs, 23°C #14 AWG (1.63 mm dia.) solid conductor with 0.030 in (0.76 mm) insulation. Full immersion of tubular specimens. Tensile Strength Retention: 76% Elongation Retention: 97% Cleaner, Isopropyl Alcohol, TT-I-735, 24 hrs, 23°C #14 AWG (1.63 mm dia.) solid conductor with 0.030 in (0.76 mm) insulation. Full immersion of tubular specimens. Tensile Strength Retention: 82% Elongation Retention: 103% Coolant, Monsanto Coolanol 25, 24 hrs #14 AWG (1.63 mm dia.) solid conductor with 0.030 in (0.76 mm) insulation. Full immersion of tubular specimens. Tensile Strength Retention: 92% Elongation Retention: 89%

补充信息

Fluid Resistance:Diesel Fuel, MIL-F-16884, 24 hrs, 35°C #14 AWG (1.63 mm dia.) solid copper conductor with 0.045 in (1.1 mm) insulation. Full immersion of tubular specimens. Tensile Strength Retention: 77% Elongation Retention: 101% Hydraulic Fuel, MIL-H-5606, 24 hrs, 49°C #14 AWG (1.63 mm dia.) solid copper conductor with 0.045 in (1.1 mm) insulation. Full immersion of tubular specimens. Tensile Strength Retention: 61% Elongation Retention: 93% Hydraulic Fuel, MIL-H-17672, 24 hrs, 49°C #14 AWG (1.63 mm dia.) solid copper conductor with 0.045 in (1.1 mm) insulation. Full immersion of tubular specimens. Tensile Strength Retention: 73% Elongation Retention: 111% Lubricating Oil, MIL-L-23699, 24 hrs, 49°C #14 AWG (1.63 mm dia.) solid copper conductor with 0.045 in (1.1 mm) insulation. Full immersion of tubular specimens. Tensile Strength Retention: 80% Elongation Retention: 124% ASTM #2 Oil, 4 hrs, 70°C #14 AWG (1.63 mm dia.) solid copper conductor with 0.045 in (1.1 mm) insulation. Full immersion of tubular specimens. Tensile Strength Retention: 68% Elongation Retention: 139% Turbine Fuel, JP-4, MIL-T-5624, 24 hrs, 23°C #14 AWG (1.63 mm dia.) solid conductor with 0.030 in (0.76 mm) insulation. Full immersion of tubular specimens. Tensile Strength Retention: 76% Elongation Retention: 160% Turbine Fuel, JP-5, MIL-T-5624, 24 hrs, 23°C #14 AWG (1.63 mm dia.) solid conductor with 0.030 in (0.76 mm) insulation. Full immersion of tubular specimens. Tensile Strength Retention: 76% Elongation Retention: 97% Cleaner, Isopropyl Alcohol, TT-I-735, 24 hrs, 23°C #14 AWG (1.63 mm dia.) solid conductor with 0.030 in (0.76 mm) insulation. Full immersion of tubular specimens. Tensile Strength Retention: 82% Elongation Retention: 103% Coolant, Monsanto Coolanol 25, 24 hrs #14 AWG (1.63 mm dia.) solid conductor with 0.030 in (0.76 mm) insulation. Full immersion of tubular specimens. Tensile Strength Retention: 92% Elongation Retention: 89%

挤压说明
DFDA-1638 Natural can be processed on a wide range of commercially available thermoplastic extrusion equipment. This material exhibits an ease of processing that is unique for highly filled non-halogen products now on the market. We suggest beginning with the recommended conditions listed below.Extruder Extruder L/D: 20:1 to 24:1 Screws Suggested: Single flight with metering section, Barrier screws, Maddock screw Screw Delivery End: Shallow rather than deep Compression Ratio: 2:1 to 3:1 Screen Pack/Inch: 20/80/20 mesh Temperature Profile Feed Zone: 300°F-325°F (149°C-162°C) Center Zones: 380°F-400°F (193°C-204°C) Head/Die Zones: 350°F-360°F (175°C-180°C) Conductor Preheat: 250°F (121°C) Draw-Down Ratio (DDR) Core Diameter less than 0.5 in (13 mm) 1:1 to 1.25:1 Core Diameter greater than 0.5 in (13 mm) 2:1 Tooling Semi-pressure tooling improves surface finish. Tube-on tooling: Retract guider-tip slightly into die. Die Single tapered short land die is preferred. Vacuum Though not usually necessary, on occasion may help obtain a tight jacket and offset any low DDR effect. Air-Gap/Cooling Water Short air gap (such as 6 in [150 mm]) and ambient water Pre-Drying Pre-drying at approximately 158°F (70°C) for 4 hours is recommended in commercially available dehumidifying dryers. Do not heat over 195°F (90°C). Colorability UNIGARD RE DFDA-1638 Natural is a colorable compound. Color masterbatch materials designed for use with polyethylene or ethylene copolymer wire and cable products are recommended. Generally speaking, color masterbatch added at the level from 0.5 to 1.0% by weight gives adequate color and disperses well in the extrusion process.

挤压说明

DFDA-1638 Natural can be processed on a wide range of commercially available thermoplastic extrusion equipment. This material exhibits an ease of processing that is unique for highly filled non-halogen products now on the market. We suggest beginning with the recommended conditions listed below.Extruder Extruder L/D: 20:1 to 24:1 Screws Suggested: Single flight with metering section, Barrier screws, Maddock screw Screw Delivery End: Shallow rather than deep Compression Ratio: 2:1 to 3:1 Screen Pack/Inch: 20/80/20 mesh Temperature Profile Feed Zone: 300°F-325°F (149°C-162°C) Center Zones: 380°F-400°F (193°C-204°C) Head/Die Zones: 350°F-360°F (175°C-180°C) Conductor Preheat: 250°F (121°C) Draw-Down Ratio (DDR) Core Diameter less than 0.5 in (13 mm) 1:1 to 1.25:1 Core Diameter greater than 0.5 in (13 mm) 2:1 Tooling Semi-pressure tooling improves surface finish. Tube-on tooling: Retract guider-tip slightly into die. Die Single tapered short land die is preferred. Vacuum Though not usually necessary, on occasion may help obtain a tight jacket and offset any low DDR effect. Air-Gap/Cooling Water Short air gap (such as 6 in [150 mm]) and ambient water Pre-Drying Pre-drying at approximately 158°F (70°C) for 4 hours is recommended in commercially available dehumidifying dryers. Do not heat over 195°F (90°C). Colorability UNIGARD RE DFDA-1638 Natural is a colorable compound. Color masterbatch materials designed for use with polyethylene or ethylene copolymer wire and cable products are recommended. Generally speaking, color masterbatch added at the level from 0.5 to 1.0% by weight gives adequate color and disperses well in the extrusion process.

备注
1 .	#14 AWG (1.63 mm dia.) solid copper conductor with 0.045 in (1.1 mm) insulation.
2 .	#14 AWG (1.63 mm dia.) solid copper conductor with 0.030 in (0.76 mm) insulation.
3 .	#14 AWG (1.63 mm dia.) solid copper conductor with 0.030 in (0.76 mm) insulation.
4 .	#14 AWG (1.63 mm dia.) solid copper conductor with 0.045 in (1.1 mm) insulation.
5 .	No Cracks
6 .	#14 AWG (1.63 mm dia.) solid copper conductor with 0.030 in (0.76 mm) insulation.
7 .	#14 AWG (1.63 mm dia.) solid copper conductor with 0.030 in (0.76 mm) insulation.